Knowledge Centre · Tool · Excavation volume calculator

Excavation Volume Calculator and Anchor Length

Enter the length, width and depth of the excavation and the excavation volume calculator shows the in-place volume, the bulked volume to haul and the number of truck loads. In addition, the same page works out ground anchor lengths. However, the results are a first estimate; the final quantities come from the design.

Excavation volume example: deep excavation with anchored shoring in Küçükçekmece, 2023
Küçükçekmece, 2023 · deep excavation with anchored shoring

Tool

Excavation volume and anchor length

Excavation

In-place and bulked volume, truck loads

Anchors

Free length and bond length

Result

First estimate; the design sets final quantities

Prepared by

Abdullah Çetintaş, Geological Engineer

Updated

November 2026

Excavation volume calculator: volume and truck loads

First, enter the length, width and depth in metres for an excavation with vertical shoring. The bulking factor shows how much more space the excavated soil takes up once it is loaded onto a truck. You can also change the truck capacity to match your own vehicles.

Excavation area600 m²
In-place volume7,200 m³
Loose volume to haul9,000 m³
Truck loads600

Geometric volume for a vertical, shored excavation. Slopes, ramps and the thickness of the retaining wall change the volume. Bulking is roughly 1.10–1.40 for soils and higher for rock; the site investigation decides.

Ground anchor length calculator

For a prestressed ground anchor, the total length is the free length plus the bond length. That is why you only need to enter the number of anchors and the two lengths; the calculator then shows the length per anchor and the total quantity.

Length per anchor20.0 m
Total anchor length2,400 m
Total bond length1,200 m

The shoring design sets the free and bond lengths. In clay the bond length for the same load is longer than in sand or rock. Anchor heads and walers are not included.

For example, the 800 anchors on our deep excavation in Küçükçekmece added up to 30,000 m. In particular, in clay the bond length gets longer for the same load, so the total grew. We describe this job on our Küçükçekmece project page.

How is excavation volume calculated?

For a vertical excavation, the in-place volume is V = length × width × depth. However, excavated soil loosens, so the volume to haul is this result multiplied by the bulking factor. Finally, the number of truck loads is the bulked volume divided by the truck capacity.

SoilApproximate bulking factor
Sand and gravel1.10–1.15
Clay1.20–1.40
Weathered rock1.30–1.50
Sound rock1.50 and above

For example, a 30 × 20 m excavation that is 12 m deep has an in-place volume of 7,200 m³. With a bulking factor of 1.25, the volume to haul is 9,000 m³; as a result, that means 600 loads with a 15 m³ truck.

What does the result leave out?

  • Sloped excavations, ramps and the thickness of the retaining wall change the volume.
  • The site investigation and the site itself set the actual bulking factor.
  • Anchor heads, waling beams and stressing tests are not included in the anchor quantity.
  • Also, the tipping site, haul distance and traffic restrictions change how long the loads take.

That is why the result does not replace a quote. In addition, we explain the items that drive shoring costs in our shoring cost guide. For a firm figure, send us your documents through the Request a Quote form.

Questions about the excavation volume calculator

The questions we hear most often about the calculators.

Calculation and results

What is the bulking factor?

It is the ratio of the volume the soil takes up once loosened to its in-place volume. For example, 1.25 means that 1 m³ of soil in the ground takes up about 1.25 m³ on the truck.

What is the difference between free length and bond length?

The bond length is the grouted part of the anchor that transfers the load to the ground. In contrast, the free length is the part between the wall and the bond zone, which does not transfer load. The shoring design sets both.

Does the calculator give a price?

No, it only gives volumes and quantities. We do not publish prices on the site; instead, we prepare our quotes from the quantities.

Abdullah Çetintaş, Geological Engineer, founder of Fen Zemin & İnşaat

Abdullah Çetintaş

Geological Engineer · Founder, Fen Zemin & İnşaat

In ground engineering and foundations since 2006. This page draws on the site experience of Abdullah and our team.

LinkedIn profile · Last updated: November 2026

Request a quote for your excavation

Send us the site investigation, the architectural drawings and the excavation depth. Then we will work out the shoring and anchor solution with you, based on quantities.